Complete measuring solutions by the right accessories.
Since 1998, the ELGO Group has dealt with the development and production of magnetically coded magnetic tapes and magnetic rings for the non-contact position detection. The production and further development of this technology is located at ELGO Batscale AG in Liechtenstein.
|
Magnetic Tape MB20 | AB20
Magnetic Tape MB20 | AB20 incremental or absolute coded
magnetic tape layout
A the cover tape is used for the mechanical protection of the magnetic tape and is glued onto the magnetic plastictape after installation
B magnetic tape band made of plastic
C magnetic conductable stainless steel tape protects from mechanical damages and is a magnetic short circuit
Elastomer-based magnetic-rings
Elastomer-based magnetic-rings radial and axial versions in different diameters
Magnetic pole rings in conjunction with the appropriate sensor technology are used wherever rotary movements, such as angular positions and speeds on axes and drives, have to be detected, monitored and controlled. The magnetic scanning principle is not only non-contact, wear-free and low-maintenance, it is also extremely robust under extreme environmental conditions. Since the complete system is bearing free, mechanical influences do not directly affect the entire sensor.
- Incremental or absolute magnetic rings
- In radial (MRR) or axial (MRA) design
- Thanks to protection class IP68 predestined for outdoor use
- Resistant to thermal, chemical and mechanical influences
The incremental rings can be combined with the CMIX, EMIX, LMIX and RMIX series as well as the battery-operated measuring and display systems of the IZ series
Magnetic rings hard ferrite
Magnetic rings hard ferrite for rotative measurements
- Interpolation up to zu 22.800 pulses/revolution
- Direct assembly on axes possible (e.g. motor shaft)
- Contactless and wear-free measuring principle
- Applicable in roughest environments (IP67)
- Vibration and shock resistant
For use with ELGO incremental sensors EMIX, LMIX, GMIX und RMIX and the battery-powered measuring and indicator systems IZ14, IZ15, IZ16
Pole length 5 mm for GMIX und LMIX sensors
Pole length2 mm for higher resolution EMIX sensors and RMIX sensor
Pole length 2.5 mm for IZ14, IZ15, IZ16
end caps
End caps optimal protection for magnetic tapes
- Optimal protection against the peel off of the magnetic tape / cover tape
- Reduce the hazard of injury by sharp edges
AP-00 Magnetic Tape Cover Profile
AP-00 Magnetic Tape Cover Profile Aluminium Cover Profile for 10 mm Magnetic Tapes
The 20 mm wide and 2 mm high aluminium cover profile can be used as an alternative to the cover tape. The magnetic tape is glued into the existing 10 mm groove without the cover tape and is therefore optimally protected. The profile is available in a length of 1 m (AP-00-1m) or 2 m (AP-00-2m). A notch on the top serves as orientation for the mounting holes.
- Alternative to conventional cover tape
- Aluminum profil (20 mm wide, 2 mm thick)
- 10 mm wide groove for the magnetic tanpe
- Available Lengths 1 or 2 meters
- With notch as orientation for mounting holes
Guide rail
Guide rail Aluminium Guide Rail for Magnetic Tapes
- Aluminium guide rail, 25 mm wide, 6 mm high
- For 10 and 20 mm magnetic tape
- Slot on both sides (1 x 10 mm, 1 x 20 mm) for magnetic tape
- Lengths up to 2 meters
- With 4.5 mm mounting holes
Guide Carriage
Guide Carriage Suitable for Guide Rail and various Measuring Systems
The FW series guide carriages are made of a special, lubricious plastic and are the perfect complement to the FS series magnetic tape guide rails. They are suitable for mounting sensor heads from the ELGO measuring system portfolio and are available in three different designs and sizes.
- Made of special sliding plastic
- For the assembly of sensors
- Different sizes available
FW2060 (80 x 48 x 24 mm) suitable for LMIX1, EMIX1, DMIX1, GMIX1A, EMSC1, LMSC1, IZ14E, IZ15E, IZ16E und IZ17E
FW2070 (80 x 48 x 33 mm) suitable for LMIX2, LMIX22, EMIX2, EMIX23, EMSC2 und LMSC2
FW2080 (100 x 48 x 34 mm) suitable for EMAX|EMAL (exclusively for the housing variant with fixed sensor outlet)
PNO SSI - PROFIBUS Converter
PNO SSI – PROFIBUS Converter simple conversion from SSI to PROFIBUS
- Up to 1,200 m cable length
- Transmission rate up to 12 MBaud
- Easy assembly due to assembly slots
- Even for older ELGO devices
The ELGO PNO SSI-PROFIBUS converter has a professional bus- interface and a 24 bits, standardized after IEC61158/IEC61784, binary coded SSI-interface with power failure bit (PFB). The converter can be used everywhere where equipment with SSI interface has to be attached to a PROFIBUS.